Last month we started at the beginning of the RFID lesson plan, reviewing the fundamental concept of frequency. We learned that frequency is the number of cycles or ‘waves’ per second and that it is measured in hertz (Hz).
While one hertz equals one wave per second, radio waves tend to cycle extremely rapidly. In contactless ID applications, frequencies are measured in units of 1000 (kilohertz–kHz) or one million (megahertz-MHz). And we found that it is the ability of transmitters and receivers to tune into certain frequencies while tuning out others that enable systems to function. For example, this tuning enables a contactless card system to ‘see’ the 13.56 MHz frequency while ignoring the 54 MHz television signal, the 824 MHz cellular phone signal, the 2.4 gigahertz (GHz) wireless LAN signal, and countless other frequencies that flow through the air at any point in time.
With this understanding of radio waves and frequency, we will now progress to a discussion of modulation–the process by which meaningful data is transmitted using radio waves.
In essence, data is ‘carried’ on radio waves. Imagine that the radio waves are a conveyor belt. The belt moves on a steady pace never stopping, never varying. At each end of the belt sits a person, one called a transmitter and one called a receiver. Periodically, the transmitter places a box on the conveyor and it moves down the belt until it reaches the receiver. The transmitter has used the conveyor belt to send the box to the receiver. Much like a transmitter uses radio waves to send data to a receiver.
Obviously, we can’t place a box on radio waves. So how is it that data is carried through the air? It is by modulating or changing some of the radio waves in a very specific manner. In fact, this is a pretty good working definition for modulation–the changing of radio waves in a specific manner in order to represent data.
As we know, data–whether it is alphanumeric, audio, video, or other–can be represented digitally as a series of ones and zeros. This is called binary data and it is the basis of all digital communication. RF uses binary data to encode and transmit data via radio waves. Rather than zeros and ones, think of it as altered and non-altered radio waves. To transmit a number, we use a specific combination of altered and non-altered radio waves to ‘code’ the number in a manner that is meaningful to the receiver.
There are three basic ways in which radio waves are altered or modulated in RF communication. They are amplitude modulation (AM), frequency modulation (FM), and phase modulation (PM). Sound familiar? AM and FM have become household names because of their use in the audio radio bands. PM is lesser known but used in many new RF systems.
Modulating amplitude refers to the process of altering the height of the radio waves. This is the original type of modulation which explains why AM is the oldest type of radio broadcast. As you can see in Figure 1, the frequency of the waves does not vary in the amplitude modulation, only the height of the waves. Amplitude modulation is the most common form of modulation used in RFID and is used in both the ISO 14443 and ISO 15693 specifications for reader to card communication.
Modulating the actual frequency of the radio waves is key to the process of frequency modulation. It is the changes in frequency that signify the zeros and ones in the binary communication. As you can see in Figure 2, the amplitude of the waves does not vary but their frequency does.
Modulating the phase of the radio waves can be thought of as bouncing the waves off of a mirror at a specific point in time–in essence, changing their up and down pattern to a down and up pattern and so on. It is the pattern of these phase changes that is used to signify the zeros and ones in the binary data during phase modulation. As you will notice in Figure 3, neither the amplitude nor the frequency of the radio waves changes–only the phase or direction of the waves.
Frequently, you will see modulation in RFID systems referred to as shift keying. The common terms are amplitude shift keying (ASK), frequency shift keying (FSK), or phase shift keying (PSK). Both ISO 14443 and ISO 15693 standards utilize ASK for modulation. Think of shift keying as the representation of data in the ‘shifting’ between states. In ASK, the waves are shifting between amplitude states or heights; in FSK, the waves are shifting between frequencies; and in PSK they are shifting between phases.
So to summarize: Modulation is the process of altering the carrier waves in a specific manner to signify meaningful data. Data is coded using binary zeros and ones that are represented through changes in the waves. These changes can be to the waves amplitude, frequency, or phase. Now you have the basics of modulation in hand. In the next installment of RFID 101, we will investigate the concept of Coding–the manner in which data is represented via modulation.